Smaller, Faster, Cheaper, Over: The Future of Computer Chips(nytimes.com)
nytimes.com
Smaller, Faster, Cheaper, Over: The Future of Computer Chips
http://www.nytimes.com/2015/09/27/technology/smaller-faster-cheaper-over-the-future-of-computer-chips.html
48 comments
On the contrary, this article omits mentioning most of the limits we're running into, probably because the reporter couldn't understand them. Dennard scaling ended almost a decade ago because of leakage. You can still put more transistors on a chip, but the benefit of doing so is going away: it allows you to put more hardware in there, but you can't afford to run it all the time because it overheats (the "dark silicon" problem), so instead of giving you a parallel speedup, you're limited to providing a wider range of alternative hardware resources. Reversible computing was an attempt to solve the power-dissipation problem, but it doesn't help with leakage currents, and it's also essentially unachievable as a practical reduction in dissipation with current technology.
(I think it's a little strange to call light with a wavelength of under 10nm "ultraviolet". It's 40 times more energetic than the single octave we call visible light; that's five or six octaves away. I think it's usually called "X-rays".)
True 3D chip design is older than 2D chip design. Bardeen and Brattain's transistor was a 3D chip. That's why it was impractical for 12 years until the planar fabrication process in 1959. Planar fabrication is not only technically important, but also necessary for our current approaches to cooling, which is getting gradually more crucial.
I agree that we're not even close to the ultimate limits of computation. If your lambda is 10 nm and your wires are 20 nm across, that's still on the order of 200 atoms across, and it's been demonstrated that you could just use one: that's almost 16 Moore doublings, or 32 years. And certainly when we figure out how to do reversible computation and molecular nanotechnology, we can reach that limit. But CMOS and X-ray lithography aren't on a path to do that.
CMOS had a great run, totally dominating electronics from about 1982 to about 2017, pushing every alternative process to the margins with its low cost and the miracle of Dennard scaling: ECL, Josephson junctions, CCDs, DNA computing, vacuum tubes, core, chalcogenide glasses. But now that's over.
But don't forget that electronics started in 1904. Vacuum tubes, planar bipolar transistors, planar bipolar ICs, and planar CMOS ICs have each had their time in the sun. Whatever comes next will be something totally different, maybe as different as vacuum tubes are from planar transistors, and there's no reason to expect Intel or TSMC to be the one to pioneer it, just as Polaroid, Kodak, and Nikon weren't the companies that pioneered semiconductor imaging sensors or flash memory.
I'd be surprised if it happened in the US or Europe. Israel, China, Korea, or Japan, possibly.
(I think it's a little strange to call light with a wavelength of under 10nm "ultraviolet". It's 40 times more energetic than the single octave we call visible light; that's five or six octaves away. I think it's usually called "X-rays".)
True 3D chip design is older than 2D chip design. Bardeen and Brattain's transistor was a 3D chip. That's why it was impractical for 12 years until the planar fabrication process in 1959. Planar fabrication is not only technically important, but also necessary for our current approaches to cooling, which is getting gradually more crucial.
I agree that we're not even close to the ultimate limits of computation. If your lambda is 10 nm and your wires are 20 nm across, that's still on the order of 200 atoms across, and it's been demonstrated that you could just use one: that's almost 16 Moore doublings, or 32 years. And certainly when we figure out how to do reversible computation and molecular nanotechnology, we can reach that limit. But CMOS and X-ray lithography aren't on a path to do that.
CMOS had a great run, totally dominating electronics from about 1982 to about 2017, pushing every alternative process to the margins with its low cost and the miracle of Dennard scaling: ECL, Josephson junctions, CCDs, DNA computing, vacuum tubes, core, chalcogenide glasses. But now that's over.
But don't forget that electronics started in 1904. Vacuum tubes, planar bipolar transistors, planar bipolar ICs, and planar CMOS ICs have each had their time in the sun. Whatever comes next will be something totally different, maybe as different as vacuum tubes are from planar transistors, and there's no reason to expect Intel or TSMC to be the one to pioneer it, just as Polaroid, Kodak, and Nikon weren't the companies that pioneered semiconductor imaging sensors or flash memory.
I'd be surprised if it happened in the US or Europe. Israel, China, Korea, or Japan, possibly.
Excellent summary, note that the deep trench transistors (aka FinFets) helped with the leakage problem significantly, but heat will always be an issue.
I've speculated that if we could figure out how to manufacture it, we could get electron scale computation out of an artfully constructed Graphene matrix. Basically a tiny Pachinko machine with electrons for balls. But at that scale you're going to need redundancy to get around quantum effects. We know you can build transistors at 7nm [1] but to what end.
[1] http://arstechnica.com/gadgets/2015/07/ibm-unveils-industrys...
I've speculated that if we could figure out how to manufacture it, we could get electron scale computation out of an artfully constructed Graphene matrix. Basically a tiny Pachinko machine with electrons for balls. But at that scale you're going to need redundancy to get around quantum effects. We know you can build transistors at 7nm [1] but to what end.
[1] http://arstechnica.com/gadgets/2015/07/ibm-unveils-industrys...
Great talk!
I don't think anyone doubts that we'll continue to make improvements in process technologies until the sun explodes, the main questions are pace and benefits.
Yes, we can create shorter channels using more/different materials. Yes, we can get stronger gate fields using more/different materials. Yes, we can start building vertically and cool the chip using microfluidics. But, all of these things take more time than previous scaling efforts, and are going to have quantum scaling benefits instead of the classical scaling benefits that we had before.
Even now, companies have a difficult choice when switching to 16nm - is it worth the cost and effort? The rules for designing chips have double width each new generation too, making it harder to physically design in addition to the less-manageable transistors. We now have a bad combination of high supply and low demand - new processes double supply due to shrinkage, but reduce demand due to design cost & difficulty.
edit: Newtonian => classical
Yes, we can create shorter channels using more/different materials. Yes, we can get stronger gate fields using more/different materials. Yes, we can start building vertically and cool the chip using microfluidics. But, all of these things take more time than previous scaling efforts, and are going to have quantum scaling benefits instead of the classical scaling benefits that we had before.
Even now, companies have a difficult choice when switching to 16nm - is it worth the cost and effort? The rules for designing chips have double width each new generation too, making it harder to physically design in addition to the less-manageable transistors. We now have a bad combination of high supply and low demand - new processes double supply due to shrinkage, but reduce demand due to design cost & difficulty.
edit: Newtonian => classical
> Even now, companies have a difficult choice when switching to 16nm - is it worth the cost and effort?
The alternative is to spread processing power over multiple cores and have programmers write code that takes advantage of that. We have a thirty year-long history of failures in that department. It has gone from "this is how we'll be writing code tomorrow" in the '80s to "this will FINALLY be a nail in the coffin of Moore's law, just wait and see" since the late 1990s.
The cost is worth it because there are a lot of high-profile industries depending on it, and there is no credible alternative yet. Until that alternative -- which will be hardware in nature, not software -- comes up, the current trend is all we have.
The alternative is to spread processing power over multiple cores and have programmers write code that takes advantage of that. We have a thirty year-long history of failures in that department. It has gone from "this is how we'll be writing code tomorrow" in the '80s to "this will FINALLY be a nail in the coffin of Moore's law, just wait and see" since the late 1990s.
The cost is worth it because there are a lot of high-profile industries depending on it, and there is no credible alternative yet. Until that alternative -- which will be hardware in nature, not software -- comes up, the current trend is all we have.
The opposite of 'quantum' is 'classical', not 'Newtonian'.
Now, I'm not even close to being able to weigh in on the physics side here... but my observation, as someone who has spent several hundred grand on servers in the last decade is that Intel is run by profit-maximizing professionals.
Look at how much better/faster/cheaper the intel stuff got after AMD's release of the hyper transport opteron.
and look at how much Intel tried to collect rent from their position of market dominance (say, by making us buy rambus and then FBDIMMs) before that.
AMD needs to step up their game.
There's another market force at work, too, and that is demand. On the consumer side of things, at least, there isn't any need for faster x86 computers, because Microsoft isn't doing it's job. It used to be that every three years, Microsoft would release another office suite that everyone needed, that ran like a dog if your computer was more than a year or two old.
I just upgraded my games box, a decade-old core2duo, to windows 10. Works fine (modulo spyware bullshit) - Microsoft has been focusing on the "mobile" market and has been putting a lot of effort into slimming down.
That, and (and I'm so shocked to say this) but it turns out that the people crowing about 'mobile is the future' were mostly right. When I was in high school, even my poor friends had desktops. Now, I know a lot of people, even technical people who only have laptops... and a lot of the people I went to high school with got rid of their desktops and now only have cellphones and tablets; nothing with a full keyboard and intel CPU at all.
If that trend continues, I would predict that we'll eventually switch our servers to whatever architecture the mobile devices use. AMD and Cavium and a handful of other companies have been talking about doing that with ARM, but so far there's nothing I can buy except at engineering sample prices.
Look at how much better/faster/cheaper the intel stuff got after AMD's release of the hyper transport opteron.
and look at how much Intel tried to collect rent from their position of market dominance (say, by making us buy rambus and then FBDIMMs) before that.
AMD needs to step up their game.
There's another market force at work, too, and that is demand. On the consumer side of things, at least, there isn't any need for faster x86 computers, because Microsoft isn't doing it's job. It used to be that every three years, Microsoft would release another office suite that everyone needed, that ran like a dog if your computer was more than a year or two old.
I just upgraded my games box, a decade-old core2duo, to windows 10. Works fine (modulo spyware bullshit) - Microsoft has been focusing on the "mobile" market and has been putting a lot of effort into slimming down.
That, and (and I'm so shocked to say this) but it turns out that the people crowing about 'mobile is the future' were mostly right. When I was in high school, even my poor friends had desktops. Now, I know a lot of people, even technical people who only have laptops... and a lot of the people I went to high school with got rid of their desktops and now only have cellphones and tablets; nothing with a full keyboard and intel CPU at all.
If that trend continues, I would predict that we'll eventually switch our servers to whatever architecture the mobile devices use. AMD and Cavium and a handful of other companies have been talking about doing that with ARM, but so far there's nothing I can buy except at engineering sample prices.
You can buy HP Moonshots with ARM cartridges for relatively realistic prices. PayPal is supposedly running some of their stuff on them.
I do not have the energy to go through sales... what is 'realistic' here?
And can they compete in cpu power per watt with the Intel Xeon D boards I can get from my local supermicro distributor? they look pretty sweet; the only real problem is the four dimm limit; I'm seriously considering those and 32gib modules right now, just because they have such a nice watts per flop.
Long-term, for it to be a realistic solution, I'll need to be able to buy compatible parts from different companies.
And can they compete in cpu power per watt with the Intel Xeon D boards I can get from my local supermicro distributor? they look pretty sweet; the only real problem is the four dimm limit; I'm seriously considering those and 32gib modules right now, just because they have such a nice watts per flop.
Long-term, for it to be a realistic solution, I'll need to be able to buy compatible parts from different companies.
Sorry, I can't say exactly. You can find R120-P30 1U boxes at GBP1500 (8core 8DIMMs) http://www.scan.co.uk/products/gigabyte-r120-p30-single-sock...
Higher density systems like Moonshot or H270-T70 are cheaper per core of course, whether they're competitive depends on your specific application. They're not at the point where they're commoditized and where you can buy parts easily though.
Higher density systems like Moonshot or H270-T70 are cheaper per core of course, whether they're competitive depends on your specific application. They're not at the point where they're commoditized and where you can buy parts easily though.
hm. $2200 in the money I use, or so. hm. the xeon D is around half that just for the board and cpu (with four dimms, but also with 8 cores... presumably 8 more powerful cores) - and after that it's just a matter of sheet-metal and a psu, so if you can deal with half the dimms, the xeon d is lower capital cost. (I mean, you can spend a grand on a psu and a case, but you have to try pretty hard.) - but the real world power usage could make the difference. Hm. Things are often cheaper priced in USD, too.
So... yes. more research is required. But thanks! I wasn't aware that gigabyte was actually shipping it's arm stuff to mortals. Hm. I still don't see it in any of my usual (USian) channels; nothing on provantage. Still, pretty cool stuff.
So... yes. more research is required. But thanks! I wasn't aware that gigabyte was actually shipping it's arm stuff to mortals. Hm. I still don't see it in any of my usual (USian) channels; nothing on provantage. Still, pretty cool stuff.
The performance and performance-per-watt of the X-Gene1 processor that thing uses don't look terribly competitive, unfortunately: http://www.anandtech.com/show/9185/intel-xeon-d-review-perfo...
Apparently it's made on a 40nm process, and it's probably not a terribly well-optimised design either, both of which go some way to explaining why it's not much good. (Though I guess it was good enough to convince Intel to release the Xeon D for a reasonable price. As you say, Intel's run by profit-maximising professionals - they can resoundingly beat any ARM server chips anyone puts out and drive them out of business, they just don't release their best chips at the best price unless they have to.)
Apparently it's made on a 40nm process, and it's probably not a terribly well-optimised design either, both of which go some way to explaining why it's not much good. (Though I guess it was good enough to convince Intel to release the Xeon D for a reasonable price. As you say, Intel's run by profit-maximising professionals - they can resoundingly beat any ARM server chips anyone puts out and drive them out of business, they just don't release their best chips at the best price unless they have to.)
Yeah, the xeon D chips are the only 13nm xeons out. Funny that. At least they didn't gimp it as hard as they gimped the E3 xeons. Sure, only four ram slots is the same... but on the e3 it maxes out with 8gb dimms. here, at least I can use 32gb dimms, which are coming down in price, and get a semi-reasonable 128g
10 years? It has already happened. Consumer chips haven't gotten much better in a decade. Most gains have been applied to power efficiency for mobile use. An unfortunate side effect is the that chip makers are learning that they can milk money for smaller improvements. I doubt we will ever return to the old <2yr Moore's law.
On the upside we might get lucky and some new innovations will come along an give us a quick bump. Tech like optical interconnects, 3D chip manufacturing, memristors, etc.
On the upside we might get lucky and some new innovations will come along an give us a quick bump. Tech like optical interconnects, 3D chip manufacturing, memristors, etc.
Huh? Moore's Law is about transistor density, not clockspeed. It absolutely hasn't paused over the past decade. See here: http://education.mrsec.wisc.edu/SlideShow/images/computer/Mo...
Processors have also gotten significantly more capable over the past decade, and if you don't believe me, go use an Athlon 64 X2 for a bit (the cream of the crop from 2005) and see how that compares to today's processors. Poorly.
Processors have also gotten significantly more capable over the past decade, and if you don't believe me, go use an Athlon 64 X2 for a bit (the cream of the crop from 2005) and see how that compares to today's processors. Poorly.
And here's a representative comparison if you want to see actual benchmarks that measure real work that processors can perform:
1. THEN: AMD Athlon 64 X2 3800+ http://www.cpubenchmark.net/cpu.php?cpu=AMD+Athlon+64+X2+Dua...
2. NOW: Intel Core i7-5820K http://www.cpubenchmark.net/cpu.php?cpu=Intel+Core+i7-5820K+...
Note that the modern one is 13 times faster, and came out about nine years later. Sounds like Moore's Law is alive and well to me.
1. THEN: AMD Athlon 64 X2 3800+ http://www.cpubenchmark.net/cpu.php?cpu=AMD+Athlon+64+X2+Dua...
2. NOW: Intel Core i7-5820K http://www.cpubenchmark.net/cpu.php?cpu=Intel+Core+i7-5820K+...
Note that the modern one is 13 times faster, and came out about nine years later. Sounds like Moore's Law is alive and well to me.
I think the more illustrative comparison is with the i7 920, which came out in 2008. In the intervening 7 years, there's only been a ~160% improvement by the standard given. That's a rate of 23% improvement per year, rather than the 130% per year that your example implies. Most of the improvement from the Athlon 64 X2 3800+ to current CPUs was concentrated in the release of the Nehelem architecture.
http://www.cpubenchmark.net/cpu.php?cpu=Intel+Core+i7+920+%4...
The i7 920 was an incredible step forward, but progress has stalled since its release.
http://www.cpubenchmark.net/cpu.php?cpu=Intel+Core+i7+920+%4...
The i7 920 was an incredible step forward, but progress has stalled since its release.
You're comparing a low-end 89W TDP chip with a 219 mm² die to a high-end 140W TDP chip with a 356 mm² die, and even then a lot of the actual improvement is front-loaded in the first few years of those 9 years.
This is true. However, if you look at the chips in average consumer laptops, I don't think they have increased in performance in line with Moore's Law.
Today's consumers are being sold cheap laptops that often have Celeron and Pentium chips, which are branded versions of the Atom design. Most of them are slower than an Intel Core 2 Duo E4400 from 2007. The big difference is that that had a TDP of 65W where a modern Atom would be more like 8W.
That dramatic reduction in TDP has been driven by ultra-thin laptop designs, which has also affected faster Core designs, especially the 4.5W Core M.
So yes, a lot of consumers are getting laptops that haven't increased dramatically in performance, and may have declined (as rated by Passmark benchmarks (1)). But they are getting thinner laptops with better battery life, and they are paying a lot less for them (maybe $200).
(1) Real-life performance is also affected by things like built-in H264 decoding, hardware acceleration in operating systems etc.
Today's consumers are being sold cheap laptops that often have Celeron and Pentium chips, which are branded versions of the Atom design. Most of them are slower than an Intel Core 2 Duo E4400 from 2007. The big difference is that that had a TDP of 65W where a modern Atom would be more like 8W.
That dramatic reduction in TDP has been driven by ultra-thin laptop designs, which has also affected faster Core designs, especially the 4.5W Core M.
So yes, a lot of consumers are getting laptops that haven't increased dramatically in performance, and may have declined (as rated by Passmark benchmarks (1)). But they are getting thinner laptops with better battery life, and they are paying a lot less for them (maybe $200).
(1) Real-life performance is also affected by things like built-in H264 decoding, hardware acceleration in operating systems etc.
CydeWeys is correct. To quote a previous post of mine:
----------------------
The fastest CPU in 2005 was (I think) the mighty AMD Athlon 64 FX-57, which PassMark rates at: 731.
Meanwhile, in 2015, we have the Intel Core i7-5930K which scores: 13,638.
--------------------
I really have no idea where this crazy idea that 2005 was the pinnacle of consumer CPU power comes from...
----------------------
The fastest CPU in 2005 was (I think) the mighty AMD Athlon 64 FX-57, which PassMark rates at: 731.
Meanwhile, in 2015, we have the Intel Core i7-5930K which scores: 13,638.
--------------------
I really have no idea where this crazy idea that 2005 was the pinnacle of consumer CPU power comes from...
When people say things like that, they usually bemoan the radical slowdown in single-thread performance improvements. For some problems that's all that matters, and the people that have such problems are understandably disappointed.
Moore's law is alive and well (at least for now) for low-power and multicore, but for single-thread desktop-class chips things have slowed down a lot.
Moore's law is alive and well (at least for now) for low-power and multicore, but for single-thread desktop-class chips things have slowed down a lot.
>I really have no idea where this crazy idea that 2005 was the pinnacle of consumer CPU power comes from...
As 'tormeh said, single-threaded performance has not improved as much since 2005. For example, the Passmark single-thread rating for the Athlon 64 FX-57[1] is 832 and for the i7-5930K[2] is "only" 2081.
[1] http://www.cpubenchmark.net/cpu.php?cpu=AMD+Athlon+64+FX-57
[2] https://www.cpubenchmark.net/cpu.php?cpu=Intel+Core+i7-5930K...
As 'tormeh said, single-threaded performance has not improved as much since 2005. For example, the Passmark single-thread rating for the Athlon 64 FX-57[1] is 832 and for the i7-5930K[2] is "only" 2081.
[1] http://www.cpubenchmark.net/cpu.php?cpu=AMD+Athlon+64+FX-57
[2] https://www.cpubenchmark.net/cpu.php?cpu=Intel+Core+i7-5930K...
To put this in perspective: for the decades before 2005 when performance per price matched 1:1 with transistor price, speeds increased roughly 100x per decade. That's 2^(10/1.5) ~= 102 for an 18 month doubling period.
So between 2005 and 1015, they only increased 2081/832 ~= 2.5. Single-thread performance increase at a given price is effectively dead (for now).
The sad thing about this (that I've been ranting about since around 2000) is that increasing parallel performance is so trivial that small companies like 3dfx were doing it with Voodoo cards back in the mid 90s. It’s only gotten easier since, so now it’s so streamlined that video card companies just keep doubling the number of cores with little deep insight into how to generalize what they are doing. Their monopolization has hurt research into things like using FPGAs for general-purpose parallel computing, and what’s stung perhaps even more than that is being locked into narrow-focus approaches like CUDA and OpenCL.
Increasing serial performance is relatively straightforward. If companies hadn't doubled down on things like caching in the race for more speed, we could have moved to small/exotic chips using rather well-understood materials like Gallium Arsenide. Probably the easiest way to go about this is to reject relying on the clout of big companies. I’d like to see an architecture like MIPS with say a 4-8 stage branch-predicting pipeline and well-understood engineering tradeoffs implemented in a SiGe or graphene processor with on the order of 10,000-100,000 transistors, running above 10 GHz. This isn’t likely to happen anytime soon, because so much has been invested in status quo fabs, but I keep hoping that some of the older fabs might throw their hands up and try retooling with some of this 90s technology rather than going out of business.
So between 2005 and 1015, they only increased 2081/832 ~= 2.5. Single-thread performance increase at a given price is effectively dead (for now).
The sad thing about this (that I've been ranting about since around 2000) is that increasing parallel performance is so trivial that small companies like 3dfx were doing it with Voodoo cards back in the mid 90s. It’s only gotten easier since, so now it’s so streamlined that video card companies just keep doubling the number of cores with little deep insight into how to generalize what they are doing. Their monopolization has hurt research into things like using FPGAs for general-purpose parallel computing, and what’s stung perhaps even more than that is being locked into narrow-focus approaches like CUDA and OpenCL.
Increasing serial performance is relatively straightforward. If companies hadn't doubled down on things like caching in the race for more speed, we could have moved to small/exotic chips using rather well-understood materials like Gallium Arsenide. Probably the easiest way to go about this is to reject relying on the clout of big companies. I’d like to see an architecture like MIPS with say a 4-8 stage branch-predicting pipeline and well-understood engineering tradeoffs implemented in a SiGe or graphene processor with on the order of 10,000-100,000 transistors, running above 10 GHz. This isn’t likely to happen anytime soon, because so much has been invested in status quo fabs, but I keep hoping that some of the older fabs might throw their hands up and try retooling with some of this 90s technology rather than going out of business.
I have little experience with hardware but I've often wondered about this. Chip manufacturers seem to be trying to fit more and more into an amount of space that continues to shrink. Why not stay at, say, 1x1" and fill that space out? I'm sure there's a good reason why not, heat or density of the connections or somesuch. I'd love a more thorough explanation however, if anyone knows.
The smaller your transistors get, the more errors you get per square inch of silicon wafer so in order to make ends meet as the manufacturing gets more and more expensive, you have to do a lot of tricks.
Tiny errors that are within a single processor can usually be fixed by disabling some cores or features and downgrading the SKU (i7 sold as i5). However, big errors are extremely costly and a few can wipe out the yield and profitability on a wafer.
If you have, for example, two 1x1 in processors on a wafer and a scratch stretching two adjacent corners of those processors, you lose both processors. If the scratch is diagonal and at the boundary between three or four processors, you would lose them all. If, however, those 1x1in units are split into .5x.5in ones, even your worst errors are unlikely to destroy the entire 2 sq in surface.
The difference in size isn't as drastic as in my example, but there are many other factors that impact yield and chip size is one of the most impactful ones (everything else being equal)
Tiny errors that are within a single processor can usually be fixed by disabling some cores or features and downgrading the SKU (i7 sold as i5). However, big errors are extremely costly and a few can wipe out the yield and profitability on a wafer.
If you have, for example, two 1x1 in processors on a wafer and a scratch stretching two adjacent corners of those processors, you lose both processors. If the scratch is diagonal and at the boundary between three or four processors, you would lose them all. If, however, those 1x1in units are split into .5x.5in ones, even your worst errors are unlikely to destroy the entire 2 sq in surface.
The difference in size isn't as drastic as in my example, but there are many other factors that impact yield and chip size is one of the most impactful ones (everything else being equal)
Die size influences yield which immensely impacts how much money you make. So you make things as small as feasible. Smaller die means more chips per wafer and smaller die means less chance of some contamination causing a particular die to be defective.
Because they want to fit as many dies as possible onto a wafer. The cost for lithography is largely per waver, so if they can cut more chips from a single waver, that is, if their chips are smaller, they can increase their profit per wafer.
That and smaller geometries tend(ed) to get faster (the electrons have to travel smaller distances) and consume less power to boost. Win win win.
This is why Intel used to beat out much better processor architectures simply by having enough money to always be at least 1 fab generation ahead.
This is why Intel used to beat out much better processor architectures simply by having enough money to always be at least 1 fab generation ahead.
Forgive my ignorance, but if the fab generation ahead was already invented, and (my understanding is) a new fab process requires completely new machinery, what stopped AMDAMD, whoever, from "skipping" a generation to catch up with Intel?
As I understand it, every fab generation requires a bunch of changes and new tricks, but they're generally in different areas of the process - and you need most or all of the tricks learnt in creating the previous generation of fab in order to build the one after that. So you probably don't save all that much time or money by skipping a generation, and in the meantime you're a generation further behind and have nothing competitive to sell.
Defect density is relatively fixed. If you have very large die, defects will take out all your chips on the wafer and leave you with zero yield. If you have very small die, you will only lose as many die as you have defects.
If you want actual industry discussion, I recommend SemiWki articles 1-5 by Scotten Jones.
https://www.google.com/url?q=https://www.semiwiki.com/forum/...
(my apologies on the link, but the direct one I tried did't work without login)
The issue isn't Moore's law (either speed or #transistors), the issue is cost per transistor. If that doesn't scale we aren't going to double the price we pay to get 2x more cores. Power/Cooling and the increasing cost of fabs has also put a dent in things.
Do you know more sources where I can read about IC manufacturing? Gwern's article [0] spurred my curiosity about the topic. EE senior here.
[0]http://www.gwern.net/Slowing%20Moore%27s%20Law
[0]http://www.gwern.net/Slowing%20Moore%27s%20Law
While it's dated (e.g. just prior to what people are saying are the heydays of CMOS, which matches my vague memory), I found this 1981 book invaluable back when I read it in the early '80s: http://www.amazon.com/Microelectronics-Revolution-Tom-Forest...
It covers in at least a little detail all the generations of semiconductors, e.g. there was a great table showing which companies were big in each. As I recall, back then TI was the only survivor, and, surprise, TI is still pretty strong as I understand it. It's discussions and illustraions of yield, what akiselev discusses here https://news.ycombinator.com/item?id=10286735 were particularly useful.
I wouldn't recommend it today (and probably didn't return to it after the '80s) except that's it pretty cheap used and will cover lots of stuff that's not so generally well known now.
It covers in at least a little detail all the generations of semiconductors, e.g. there was a great table showing which companies were big in each. As I recall, back then TI was the only survivor, and, surprise, TI is still pretty strong as I understand it. It's discussions and illustraions of yield, what akiselev discusses here https://news.ycombinator.com/item?id=10286735 were particularly useful.
I wouldn't recommend it today (and probably didn't return to it after the '80s) except that's it pretty cheap used and will cover lots of stuff that's not so generally well known now.
Although it requires watching, I'm a fan of https://youtu.be/NGFhc8R_uO4
[deleted]
Are gallium based chips completely non-viable or something? I thought they were the next big thing in chip materials that would let us get past the Moore's law restrictions in silicon?
According to the USGS, gallium arsenide use is higher than ever, but it remains niche, because it's just a minor tweak to the silicon bandgap structure, especially for bipolar circuits, where people have been fabricating high-performance CPUs in it since the 1980s. It doesn't work even adequately for CMOS, but even if it did, it doesn't solve the problems with Dennard scaling.
If you're looking for exotic materials to bail us out, it might be a little less hopeless to look to diamond or to high-temperature semiconductors.
If you're looking for exotic materials to bail us out, it might be a little less hopeless to look to diamond or to high-temperature semiconductors.
They are really, really expensive to make compared to silicon, and I want to say they run hotter (but my memory is fuzzy).
Silicon has never really been the most ideal material for transistors, but it has always been so cheap in comparison to be the most cost effective.
The joke about GaAs is that it will always be the material of tomorrow. (They've been using it in lab settings for decades)
Silicon has never really been the most ideal material for transistors, but it has always been so cheap in comparison to be the most cost effective.
The joke about GaAs is that it will always be the material of tomorrow. (They've been using it in lab settings for decades)
Agree, Lidow's championing of gallium (along with many others) is far from going unnoticed. Some people are still however caught up on the cost aspect and feel the economies of scale silicon based chips have are too high to break. Frankly, this is just not true anymore...
I don't think the author of this article knows about them, or they didn't fit into the narrative.
Searched for 'parallel' and 'core' on the page - no matches found.
Point being, there's many billions of dollars in revenue here at stake, and chip companies are doing their damnedest to solve these problems. They've solved every challenge so far, and there's no real reason that these latest challenges are fundamentally unconquerable in ways that the previous ones were not. An article highlighting the current challenges is useful, but one positing that they can't be overcome is sensationalist.